Closer to the real amp
How far the capture is from the real amp* (shorter is better)
NAM A2-Lite captures replace the factory's AM4, so pick attack and harmonics come out like the real amp.
Unlock the hidden power of your Tank‑G or Tank‑B.
A free firmware update for the Tank‑G and Tank‑B, with NAM captures, your own IRs and an Android app.
Scene 1 is playing.
Factory firmware 99, recording on Android and the full editor on a tablet. Update the pedal, and the Android app too.
Got a Tank‑G v2 with M‑VAVE's latest firmware? UltraRig installs on it now.
Plug the pedal into your Android phone with a USB cable and record your sound, no dropouts.
Hold your Android tablet sideways and the app shows the whole editor, like on a computer.
The app no longer heats up your phone while the pedal is connected.
The Tank-G's factory software locks you into four slots in a fixed order. UltraRig gives you up to 16 effects to put anywhere you like.
Drag a pedal to move it. Or tap one, then use these buttons or the arrow keys.
New software for the same hardware. UltraRig puts the whole chip to work.
NAM A2-Lite captures replace the factory's AM4, so pick attack and harmonics come out like the real amp.
Cabinet files play almost twice as long, so the low end and the room stay in. Use your own.
NAM captures are trained at 48 kHz. UltraRig loads your .nam files as they are, no conversion, and runs everything at 48 kHz from input to output.***
Up to 16 of the 40 effects per sound, in any order and even in parallel. In a parallel group in POST, L / R sends each side to one branch and Wide puts one in each ear (Wide is for headphones). Since alpha 13, two reverbs, a delay, a chorus and a compressor fit together on most pedals. If a preset is too heavy, you get a notice, and Ease it turns oversampling off, never an effect.
And you're in control. Edit from your computer or phone, and give each footswitch an action for a tap, a double tap and a hold. Jam along with Bluetooth music: songs from your phone play through the pedal. Plug it into your computer and it's a USB sound card too, to record or re-amp.
*Error (ESR) against the real amp: lower is better, and NAM calls under 0.05 good. My own test: one high-gain amp captured into both formats with the same processing budget and 75 minutes of training each, measured on guitar the models had never heard. AM4 keeps improving with longer training, so against the factory's own captures the gap may be closer to 2 to 3×.
**At 44.1 kHz: how far the capture drifts from its own sound at 48 kHz (ESR 0.143, about the gap between AM4 and the real amp). At 48 kHz: its error against the real amp (0.024). Lower is better.
***Since factory firmware 98 (October 2026), M-VAVE's own firmware also loads NAM captures, but only after converting them in its app, and the pedal still runs at 44.1 kHz, effects included.
The factory figures on this page are the Tank-G's.
The path your sound takes inside the pedal, from the guitar to your amp or headphones. Tap a stage to see what happens there.
What changes in the sound, explained without the jargon.
A capture is a recording of how a real amp behaves. Play softly and it cleans up, dig in and it growls, the way the real one does.
A cabinet file holds the sound of a speaker and its microphone. The Tank-G's factory editor cut those files short. UltraRig plays almost twice as much of each one, at 48 kHz, so the low end and the room come through.
Digital distortion can add a harsh fizz that a real pedal never makes. UltraRig works out every drive at a higher internal rate, which keeps that fizz out.
UltraRig runs the chip faster and hands the heaviest math to a calculator built into it. The amp and the cabinet take less of the chip's time, so more effects fit in one sound.
Everything on board: classic pedals and studio effects, plus the banks for your amp captures and speaker cabinets. More effects come with every release. In stereo headphones, chorus, vibrato, delay, Ping-Pong, Dual, four of the reverbs, the Doubler and the Rotary spread across both sides, switched on per preset. Pick a group to see what's in it.
15 slots for your amp captures: NAM A2 Lite files, converted in the editor. The Amp block plays one of them.
8 slots for speaker cabinets: your own .wav files at 48 kHz, up to 85 ms each. The Cab IR block plays one of them.
Everything you need on stage, under your feet. Try them here.
Each preset keeps four scenes: the same chain with different effects on and different knob settings. Clean verse, crunchy chorus, lead with delay, all one stomp away.
Every footswitch does three jobs: one for a tap, one for a double tap and one for a hold. You choose them, and the lights around the switch show what's on. In Scenes, double tap footswitch 1 or 4 to jump to the previous or next preset.
Tap a footswitch on the beat and the delay repeats in time with the song. Try it: tap the button a few times.
Put a pitch shifter first in the chain and the whole guitar sounds lower, with no retuning. Pick a tuning.
The same editor in UltraRig Editor, on Windows or Mac, and in the Android app over Bluetooth, in English or Spanish.
Drop .nam and .wav files on the page, several at once
Add an effect between two others, or split the chain into A and B branches
Set footswitch actions and light colors
See how much battery the pedal has left
Save a preset as a file and share it
Pair your phone once: nobody nearby can change your presets
UltraRig alpha 13.1 is out, free and public. You can install it today, as long as you know what an alpha means.
This is an alpha: expect bugs. It works well, but it keeps changing: I build it on my own and the community helps me by testing it, so you use it at your own risk, at home or on stage. Under heavy load the pedal can still restart by itself. Keep the backup the installer makes.
Every version is published on GitHub. This button always opens the newest one.
Get the latest release Free. Opens GitHub in a new tab. Download for Black Box (Windows) Download for Black Box (Mac) Black Box with factory firmware 016, 017, 019 or 020, on Windows and Mac. 022 and 023 are on the way.Free, no account needed. The download starts right away.
Control your pedal from your phone over Bluetooth. The app controls a pedal that already runs UltraRig: install UltraRig on your pedal first with the installer, then open the app. Updating the pedal? Update the app too: the alpha 11 app connects, but it doesn't show what's new in alpha 13.1.
The installer and UltraRig Editor, in one file for your pedal. Tried on an Apple Silicon Mac. The first time, open it from System Settings > Privacy & Security > Open Anyway.
You need a Tank‑G (factory firmware 97 or 98, or 99 on the v2) or a Tank‑B (factory firmware 100), v1 or v2, a computer with Windows 10 or 11 or a Mac, and a USB data cable. See what you need
Unzip the package for your pedal anywhere, for example on the Desktop, and read README.txt. Keep all its files together.
Plug the pedal into the computer, switch it on and close M-EFCS and UltraRig Editor. Run UltraRig-Installer.exe and click "Install UltraRig" ("Update UltraRig" if you already have it). If Windows warns about an unknown publisher, click "More info", then "Run anyway". The same may happen with UltraRig Editor.
It backs up the whole pedal to your computer first, then writes UltraRig and restarts the pedal. Don't unplug it or switch it off until the window says it's installed.
Open the UltraRig shortcut the installer leaves on your desktop: it starts UltraRig Editor. Or, now that the pedal runs UltraRig, open the Android app. Then copy your backup, in Documents\tankg_installer, somewhere safe: it's the only way back to factory with your own presets and captures.
Not sure about your pedal? The free pedal check only reads it and never writes anything.
Run the pedal checkOn 97 and the installer says it can't use its settings area? Install 98 and try again; on the v2, 99 works too.
The installer keeps a full copy of your pedal, and with it you go back exactly as it was.
The installer checks your pedal before writing anything and, if it isn't supported, stops without changing anything. If yours isn't on the list, open an issue on GitHub.
Safe enough to try if you follow the steps, but not risk-free. If you can't be without the pedal for a while, wait for a later version.
UltraRig is a personal, independent project, not connected to M-VAVE. It runs on the Tank-G and the Tank-B, v1 and v2, today. More pedals may follow, and you can help pick which.
Four things you can hear and use. The amp captures are NAM A2-Lite, running natively on the pedal with no conversion: in my test their error against the real amp was 0.024, about 5 times lower than the factory's AM4 at 0.120. Everything runs at 48 kHz from input to output, the rate NAM captures are trained at, while the factory system works at 44.1 kHz. Cabinet IRs play 1.8 times longer, so the low end and the room stay in. And one sound holds up to 16 of the 40 effects, 4 times more than the factory, in any order and even in parallel.
Safe enough to try if you follow the steps, but not risk-free. The installer checks the model and the firmware before it writes anything, backs up the whole memory twice and compares the copies, and never touches the bootloader, so if an install gets cut off, the pedal waits in a recovery mode the installer can write again. Even so, this is alpha software from a personal project, writing firmware always carries a small risk, and there's no warranty if something goes wrong. If you can't be without the pedal for a while, wait for a later version.
UltraRig replaces the pedal's whole system, so the factory presets, effects and captures aren't available while it's installed. Before anything changes, the installer saves a full backup of the pedal on your computer. Go back to the factory system any time and everything returns exactly as it was.
Yes, whenever you want. Open the installer, choose the factory option and it puts your backup back. Keep that backup file safe: it is the only copy of your pedal's original memory. Lost it? On a Tank-G v2, since alpha 10, the installer can still go back with M-VAVE's official firmware file, with the factory amps, IRs and presets (not on the v1 or the Tank-B yet). Your own M-VAVE presets and captures only come back with the backup.
Not since alpha 10. Up to alpha 9.1 UltraRig loaded AM2, AM3 and AM4 files as a test; alpha 10 takes that engine out to make room for what comes next. I suggest NAM captures anyway: in my test they were about 5 times more accurate. Your M-VAVE captures stay in your backup and come back if you go back to factory.
No. UltraRig is an independent project, not made or supported by M-VAVE.
Nothing. It is free for personal, non-commercial use.
From GitHub, free and with no account. The Download section of this page has the file for your pedal (v1 or v2), for Windows or Mac; the same file works for the Tank-G and the Tank-B. The Android app is on the same release page, and all versions are listed there.
Download the zip for your version, unzip it and run UltraRig-Installer.exe on Windows, or open the Mac file for your version. It checks your model and firmware, backs up the whole pedal and writes UltraRig. The same installer moves you to each new version later, and it can go back to factory too. On a Tank-B it works the same way. It works with factory firmware 97 or 98 on the Tank-G (and 99 on the v2) and 100 on the Tank-B.
Yes, a free Android app that controls the pedal over Bluetooth. It only works with a pedal that already runs UltraRig, so install UltraRig on the pedal first with the installer, then open the app. In the app you add an effect between two others with one tap, load several IRs or captures at once, and it remembers your capture and IR folders. On a tablet held sideways, it shows the full editor, like on a computer. Download it from the same GitHub release page. On a computer there's UltraRig Editor, which the installer sets up on Windows and on a Mac. Updating the pedal? Update the app too: the alpha 11 app connects, but it doesn't show what's new in alpha 13.1. The iPhone is not covered yet.
Almost always the pedal still has the factory firmware. The app controls a pedal that already runs UltraRig, so install UltraRig on it first with the installer (the Download section has it for Windows and Mac). Then switch the pedal on and open the app again.
While the installer works, that disk is the pedal. Choose Ignore, never Initialize. If macOS asks about a new accessory, choose Allow.
Yes. The IR bank has 8 slots for your own .wav files at 48 kHz, up to 85 ms each. The capture bank holds 15 NAM A2 Lite captures, converted in the editor. Both load from the editor.
Yes, since alpha 11. In the editor you can export one preset, or all of them, as a file, on your computer or your phone, and import it back into any slot. Send it to a friend over WhatsApp or post it on a forum. Tick the options to include the capture and the IR the preset uses. If you import a preset that needs a capture or an IR you don't have, the editor tells you and loads the rest. It also shows what belongs to each scene and what belongs to the whole preset.
In your headphones, yes, since alpha 11. Chorus, vibrato, delay, Ping-Pong, Dual, the Hall, Room, Cloud and Shimmer reverbs, the Doubler and the Rotary spread across both sides. Turn it on per preset with the Stereo switch on the home screen. Since alpha 13 you can also send left and right to their own branch after the amp and join them Wide, one in each ear. The 1/4-inch and XLR outputs stay as they were.
Thousands are shared free online, for example on TONE3000. Pick files with the A2 architecture; the editor converts them. Full rig captures, with the amp and the cabinet together in one file, are the best fit: the pedal then has more CPU left for effects.
Yes, since alpha 2. Download the v1 package: the installer checks which model you have and won't install the wrong one.
Yes, since alpha 9, on the Tank-B v1 and v2 with factory firmware 100 (other versions aren't supported yet). Download the package for your version (v1 or v2): the same zip has the Tank-G and the Tank-B firmware, and the installer picks the right one from what the pedal reports. For bass, alpha 9 also brings a tuner that reads the low B, a 6-band EQ and a crossover to split the lows from the rest.
Yes, since alpha 13.1, on the M-VAVE Black Box with factory firmware 016, 017, 019 or 020. Download the Black Box package for Windows or Mac from the Download section; it has its own installer, which checks your pedal before writing anything. 022 and 023 are on the way.
On the Tank-G, 97 or 98, and 99 on the v2; on the Tank-B, 100. Both on the v1 or the v2 (download the package for your version: each one has the Tank-G and the Tank-B firmware). 98 was tested on the Tank-G v2; on the v1 it hasn't been tried yet. A Tank-G v2 on 96 or older? Update it with M-VAVE's M-UPGRADE (it installs 99), then run the installer. Other versions: install 97 or 98 first (100 on the Tank-B). On 97 and the installer says it can't use its settings area? Install 98 and try again. Rebrands (Lekato, Playwell, Yuimer, NMD) haven't been tested. The installer keeps a full copy of your pedal, checks it before writing anything and, if it isn't supported, stops without changing anything. If yours isn't on the list, open an issue on GitHub.
Yes, since alpha 7. MASTER always sets the output volume. The others edit the sound in Live mode (tap B+C); in Preset mode they do nothing. Everything else you set from the editor or the Android app.
No. The installer and UltraRig Editor come for Windows 10 or 11 and for the Mac, and on a phone there's the Android app. There is also a Linux installer, a first version for testing, on the GitHub release page.
Not yet. The app is Android only for now.
Yes. Since alpha 10 the editor and the Android app speak English and Spanish: they follow your system language and you can switch it in Settings. The installer follows your Windows language, and the guides come in both.
Yes, since alpha 13. Pair UltraRig from your phone's Bluetooth menu and play music through the pedal, like a speaker, to jam over it. It mixes in after your effects and it's on out of the box. Volume and on/off are in Settings > Connections > Bluetooth music, and switching it on or off works right away. Never use it? Tick "Give its memory to effects" and restart the pedal: heavy presets get more room. To pair another phone later, hold B+C first.
Yes, since alpha 13: plug it into your computer and it shows up as "UltraRig Audio", a USB sound card at 48 kHz and 24 bits. In Settings > Connections > USB audio, pick Processed (stereo), Processed + dry (your sound on the left, the dry guitar on the right, to re-amp later) or Stereo + dry on 3 channels. It applies after you unplug the cable and plug it back in. To play, listen through the pedal's headphones; to record, use a program in exclusive mode (WASAPI): the round trip is about 31 ms. While USB audio is open, a few fewer effects fit. Since alpha 13.1 it also works plugged into an Android phone.
MIDI. I'm testing it on my pedal, and it'll arrive once it's properly tested. Follow the news at ultrarig.app/news.
Four things you can hear and use. The amp captures are NAM A2-Lite, running natively on the pedal with no conversion: in my test their error against the real amp was 0.024, about 5 times lower than the factory's AM4 at 0.120. Everything runs at 48 kHz from input to output, the rate NAM captures are trained at, while the factory system works at 44.1 kHz. Cabinet IRs play 1.8 times longer, so the low end and the room stay in. And one sound holds up to 16 of the 40 effects, 4 times more than the factory, in any order and even in parallel.